Fencing Services in Perth, Built To Last

As a rough guide, a standard 1.8m Colorbond boundary fence in Perth generally runs somewhere around $90–$130 per lineal metre installed, though the real figure depends on the length of the run, your site, access, soil, how many gates you need and your colour choice. Sloping blocks and taller fences sit higher. The only way to get an accurate number is a free on-site measure and quote — every job's a bit different.

For most standard side and rear boundary fences up to 1.8m, you generally won't need council approval. Front fences are where it gets stricter — many councils limit solid fencing in the front setback (often to around 1.2m) and require the portion above to be visually permeable, and corner blocks have sightline (truncation) rules. Rules vary by council and suburb, so it's always worth checking with your local council first — and we're happy to talk you through what's typical.

Under the WA Dividing Fences Act 1961, neighbours usually share the cost of a "sufficient" dividing fence 50/50. The standard process is to give your neighbour written notice before the work, including your request for them to contribute half. If one neighbour wants something dearer than a basic sufficient fence, they typically cover the difference. Any written agreement you both sign overrides the Act, so it's worth getting things in writing.

A properly installed Colorbond fence will typically last 20–30 years or more. The steel is coated with a zinc/aluminium alloy and baked-on paint that resists rust, UV and fading. The big variable is the install — correct post depth and proper concrete footings are what stop it leaning or rattling in Perth's wind, which is why the quality of the installer matters as much as the material.

Good Neighbour Colorbond looks the same clean, finished way on both sides — so you and your neighbour see an identical fence. Standard Colorbond has the rails visible on one side. Good Neighbour is the most popular pick for shared dividing fences and is often the fairer option when both sides are chipping in.

Yes. On a slope we can either step the fence down in sections or rake the panels to follow the ground, depending on the look you're after and how steep it is. Bigger level changes sometimes need a retaining wall first — we can handle both together, which usually works out tidier and more cost-effective than doing them separately.

Yes — we handle the full job: removing and disposing of your old fence, setting the new posts to the right depth for your soil, and leaving the site clean. If your old fence contains asbestos (common in some older Perth fences), that needs licensed handling and is quoted separately.

Generally yes — aluminium slat fencing usually costs more per metre than standard Colorbond, because of the material and the extra labour in setting individual slats. What you get for it is the modern architectural look, the adjustable spacing, and a finish that won't rust even in coastal suburbs. Lots of people use it for front fencing or feature sections and run Colorbond along the rest of the boundary to balance the budget. We'll quote your exact job on site.

It comes down to the gap between the slats. Tight spacing (around 10mm) gives you near-full privacy while still letting air through; wider gaps (20–25mm) let in more light and breeze with a more open feel. We can adjust the spacing to suit what you want and any council requirements for your area.

No — aluminium doesn't rust, which is exactly why it's such a strong pick for Perth's coastal and salt-air suburbs where steel and timber struggle over time. The powder-coated finish is UV-stable too, so it won't peel or fade the way paint on timber does.

Both. Horizontal slats are the more popular, contemporary look across Perth right now, but vertical works well too and can suit certain frontages better. We'll talk you through which suits your place and the effect you're after.

Effectively none. An occasional hose-down to clear dust or salt is all it needs — no painting, oiling or treating. That low upkeep is a big part of why it's become so common in Perth's newer estates.

Aluminium slats come in a full range of durable powder-coated finishes. Popular choices around Perth include Monument, Woodland Grey, Surfmist, Satin Black and timber-look finishes. The coating is baked on, so it holds its colour in the sun for years.

In WA any pool or spa with more than 300mm of water must have a compliant barrier. The key requirements: at least 1,200mm high, no gaps over 100mm, a non-climbable zone of 900mm on the outside (clear of anything a child could climb), and a self-closing, self-latching gate that opens away from the pool with the latch at least 1,500mm up. The full standard (AS 1926.1) is detailed, so it's worth having it checked by someone who installs to it regularly.

The rules changed on 21 June 2024 — since then, most standard pool fences no longer need a building permit. A permit is still required in specific cases, such as where the barrier also acts as a fall-protection balustrade (a drop of 1m or more), masonry barriers over 0.75m, non-masonry barriers over 1.8m, or certain high-wind regions. Your pool still needs to be compliant and is subject to council inspection — we build to the standard so it passes.

Local councils are responsible for pool barrier compliance and carry out periodic inspections — most commonly around every four years, though it varies by council. Keeping the barrier maintained (gate self-closing properly, no new climbable objects nearby) between inspections is the owner's responsibility.

It can, but only if it meets the barrier rules — generally at least 1,800mm high on the inside (pool side) with a 900mm non-climbable zone, and no footholds. Not every boundary fence qualifies, so it needs checking against the standard. We can advise whether yours works as part of the barrier or whether a separate pool fence is the safer call.

We install tubular (aluminium/steel) pool fencing in Flat Top, Loop Top and Spear Top styles, powder-coated in colours like Black, Monument and Woodland Grey. Flat Top is the most popular for its clean, modern look. All styles are built and installed to meet WA compliance.

A compliant pool gate must be self-closing and self-latching from any position, open outward away from the pool, and have the latch at least 1,500mm above ground. The self-closing hardware has to actually pull the gate shut and latch it every time — we fit compliant hinges and latches on every pool job and never cut corners on it.

With quality treated pine, proper capping and good installation, a pine lap fence can give you many years of service in Perth conditions. Timber does need a bit more care than steel — the odd coat of oil or stain helps — and it can eventually warp or weather over time, which is worth weighing up against a material like Colorbond.

It comes down to the look you want and how much upkeep you're happy with. Pine lap gives that natural timber appearance that suits older and rural-style homes; Colorbond is lower-maintenance, won't rot or attract termites, and tends to give better value over the long run. We'll give you an honest steer on which makes more sense for your place — we're not here to push one over the other.

More than steel or aluminium, yes. To get the best life out of it, timber benefits from being sealed or oiled periodically and kept clear of constant moisture at the base. Proper capping on top helps shed water and slows weathering. It's not a huge job, but it's not a set-and-forget option either.

Treated pine is designed to resist rot and insect attack, and quality installation with the right rails, posts and capping goes a long way. That said, all timber can move or weather over the years in Perth's climate — which is normal for the material. If low maintenance is your priority, we'll let you know where Colorbond might suit you better.

The same WA Dividing Fences rules apply regardless of material — neighbours generally share the cost of a sufficient dividing fence 50/50. If you want a dearer option than a basic sufficient fence, you'd usually cover the difference. Give your neighbour written notice before the work and get any agreement in writing.

As a general rule across WA councils, a retaining wall over 500mm high needs a building permit, and walls at that height typically need to be designed by a structural engineer. Lower walls can also need a permit if they encroach on a boundary, affect a neighbour's land or change site drainage. It varies by council, so we'll advise what's needed for your site and can arrange engineering if required.

Generally, the person who changes the level of the land — by cutting or filling — is responsible for the retaining wall and its upkeep. Importantly, retaining walls are not covered by the Dividing Fences Act (a dividing fence doesn't count as retaining), so cost-sharing isn't automatic the way it is with fences. Where both neighbours have altered levels, it's usually negotiated proportionally. It can get complex, so it's worth confirming with your council.

We build in concrete sleeper and timber sleeper, chosen to suit the height, load and look you're after. Concrete sleepers are the stronger option for taller walls and come in smooth or textured finishes; timber sleepers give a more natural look. We get the footings and drainage right on every wall so it stays put.

It's the single biggest reason walls fail. Without proper drainage behind the wall — ag-drain and gravel backfill with weep holes — water pressure builds up and can push the wall out, crack it or make it lean. Getting the drainage right from the start is the difference between a wall that holds for decades and one that moves in a few years.

Yes, and it's almost always tidier and more cost-effective than doing them as two separate jobs. We build the wall first, then install the fence on top so everything lines up cleanly. A dividing fence is normally positioned on the higher side of a wall along a shared boundary.

Yes — that's the idea. We build gates to match your fencing so it looks like part of the same job, not an afterthought: Colorbond gates with Colorbond, aluminium slat gates with slat fencing, tubular gates with pool fencing and timber gates with pine lap. We can match a new gate to an existing fence or build both together.

We specialise in quality manual gates — single, double, sliding and driveway gates — built strong and hung true. We don't do gate automation, so if you're after a motorised setup we'd point you to an automation specialist for that side of it.

Anything from a standard pedestrian walk-through gate for side access up to wide double or sliding gates for driveways. For wider driveway openings, double gates or a sliding gate are the usual solutions. We build to suit your opening and how you'll use it.

Usually it's undersized posts or poor hinges — a gate gets used every day and puts a lot of leverage on its supports. We hang every gate on quality hinges with proper post support and footings so it swings true and doesn't drop or drag. That's the difference between a gate that lasts years and one that sticks after six months.

Depends on the gate: standard D-latches, key-lockable latches, magnetic latches for pool gates, and heavy-duty drop bolts for double and sliding gates. For pool gates we fit compliant self-latching hardware as standard. We'll walk you through the options for how you use the gate.